How to Fix a Washing Machine That Won’t Drain – Quick Solutions 2024

When a washing machine is not draining, it can be a rather annoying problem, yet a multitude of problems can be corrected with some basic troubleshooting. Below are some of the possible solutions that you can follow out to solve the problem in question. If the problem continues, the washing machine repair Fort Lauderdale can be consulted for proper repair services. 

How to Fix a Washing Machine That Won’t Drain

1. Clean the vertical part of the drain hose 

Another usual cause of why a washing machine does not drain is through accumulated clogs in the drain hose. 

• Remove the Drain Hose: Switch off the washing machine and get it detached from the building walls. Open the slot at the back of the machine and take out the drain hose. 
• Inspect and Clear the Hose: The first step is to look at the hose to see if it is kinked or has some obstructions. If you discover any clogs, you should ideally use a long brush or a drain snake to get rid of them. Make sure the hose is not twisted or squeezed which can also hinder proper drainage.  

2. Clean the Pump Filter 

Some models of the washing machines are equipped with the pump filter which can be blocked by such things as debris, lint, or coins. 

• Access the Filter: Find the pump filter; usually, they are located behind a tiny flap in the front or at the bottom of the washing machine. 
• Clean the Filter: Put a disposable towel and a shallow vessel with water beneath it in front of the filter to allow for collection of the water. Twist off the filter cap and clean up the interior of this part for any remaining chaffs. After using the filter you should clean it well and then only place it in the machine. 

3. Inspect the Drain Pump 

However, if clearing Hose and filter does not help then there may be an issue with the drain pump. 

• Check for Obstructions: Locate the pump and using a screwdriver, open the access panel to check if there is any blockage. Remove any visible debris. 
• Test the Pump: If you have a pump that is noisy, and it does not work, then probably it is as good as done. Take the washing machine off the power source, unfasten the pump, and verify that it has no continuity with an ohmmeter. If it is so, replace it with a new pump.  

4. Confirm the Lid Switch Assembly 

Lid switch of top loading washing machines locks the machine from operating unless the lid is closed. 

• Test the Switch: Put pressure on the lid switch to try and hear a click if you hear it, know that the switch is bad. If you can’t hear a click, then the switch could be worn out and should be replaced by another better one.  

5. Check the Drive Belt 

The drive belt assists the drain pump to work through the motor which is connected to it. 

• Inspect the Belt: Laying the washing machine on its side also gives a good view of the belt used to help turn the drum and determine whether it needs replacement or not. If the belt is either worn out or elongated it will be required to be replaced by a new one.

6. Perform a Master Reset 

At other times, restarting is known to be the cure for most problems. 

• Reset the Machine: Wait for the machine to stop, turn off the washing machine from the power source and then wait for approximately one minute. Then, plug it back in and open and close the door six times within 12 seconds are the instructions to repair it. This can bring back the computer of the equipment to its factory settings which can seriously help in correcting the drain problem. 

Ensure that the Water Level Control is turned on. 

Another possible cause of your washing machine not draining or spinning is that it has a problem with the water level control. This control assesses the quantity of water it requires to commence with its drill before flooding the washer. 

• Inspect the Water Level Control: To access this probe, you need to open the control panel of the washing machine and identify the existing plastic tube that connects to the water level valve. 
• Clean the Tube: If the tube is blocked, use vomiting tube vinegar to force the blockage out of the tube . If the valve is itself rusted, probably the valve would have to be replaced.  

Clean the Coin Trap 

Some washing machines have what is known as a coin trap that tends to help filter out any small objects that could otherwise end up damaging the pump or lead to a blockage in the drain. 

• Locate the Coin Trap: This is located under the dirt cup, that’s why to locate it you should check the user manual. It is often located in a door on the front or bottom of the machine, although some are internal. 
• Empty and Clean the Trap: To clean the specific area, first, open the coin trap and take out anything that has accumulated in it. Before fitting a fresh one, ensure it is clean to its best.  

Ensure Proper Installation and Positioning

• Level the Machine: Wash your clothes in a washing machine which has all its four feet firmly placed on the floor. An unequal machine could therefore result in incorrect draining. 
• Check the Drain Hose Position: Check that the drain hose is not pushed too far into the drain pipe as it will siphon which will affect its drainage process. The hose should somehow be held in place but not be too far down the pipe that it cannot come out or be removed. 

Conclusion

It is rather simple and if you follow the above mentioned steps, you can effectively solve the problem of the washing machine not draining. Daily and proper care as well as frequent cleaning of the pieces can help deter numerous issues. 

However, if the mentioned solutions do not solve the issue, it is advisable to seek the services of washing machine repair Fort Lauderdale. They can address some of the more intricate problems with your washing machine and fix them, getting your washing machine back to functionality.